Service · 3D scanning

3D scanning that measures wear on mining and engine equipment.

Condition monitoring tells you that something is wearing. A 3D scan measures how much: the metal that is left on liners, chains, buckets, shafts and cylinder bores, to a tolerance we agree with you before we start.

  • Tolerance and limits agreed before we scan
  • Graded pass, monitor or fail, in a PDF and a spreadsheet
  • You keep the scan data for the next comparison

Four example jobs

Watch a scan become a measurement.

A chain from a real machine model, a wear plate, an engine bore and a plate scanned over time. The numbers are made up to show how a job reads.

An illustration with made-up numbers, not a customer measurement. Real jobs are scoped with you: the part, the tolerance and the limits.

Read the four demos as text

Machine chain

A run of five flight sections of the machine’s conveyor chain, taken from its 3D model, is scanned with a laser sweep and laid over the chain as made. Wear shows as colour: the worst is 5.8 mm on a flight tip, against an example limit of 8 mm. Stretch shows as the scan drifting away from the model: the pitch has grown 2.4%, from 362.5 mm to 371.2 mm, so the fifth flight sits 35 mm past where it should, against an example limit of 3%. Both are above 70% of their limits, so the chain is graded Monitor.

Wear plate

A laser scanner records the surface of an 80 mm chute wear plate as a cloud of 3D points. The scan is aligned to the plate as it was made and the distance of every point from that shape is shown as a colour map. The thinnest point is 38 mm, so the worst wear is 42 mm at the centre of the plate. With the example limits of Monitor below 42 mm and Fail below 25 mm, the plate is graded Monitor.

Engine bore

A cylinder bore with a nominal diameter of 130.000 mm is scanned all the way round. The largest diameter is 130.088 mm and the smallest 130.060 mm, so the ovality is 0.028 mm. Against the example limits of +0.150 mm for diameter wear and 0.050 mm for ovality, the bore is within limits and can stay in service. The shape in the picture is exaggerated 740 times so it can be seen.

Wear over time

The same plate is scanned four times, each aligned the same way. The thinnest point goes from 80 mm to 66 mm, 52 mm and 38 mm, a wear rate of about 4.7 mm a month. It crossed the Monitor limit between the third and fourth scan. At that rate, as a straight-line estimate, it reaches the 25 mm Fail limit in about three months.

What we scan

Mining equipment, engines and drivetrains.

Anything where the metal that is left decides whether a part is repaired, rebuilt or kept in service.

Mining equipment

  • Crusher and mill liners
  • Conveyor and drive chains: link wear and pitch stretch
  • Bucket teeth, lips and adapters
  • Haul truck bodies and chutes
  • Conveyor drums and pulleys
  • Shafts, bearing seats and gearbox housings
  • Hydraulic cylinder rods

Engine and drivetrain

  • Cylinder bores and liners: diameter, ovality, taper
  • Crankshaft and camshaft journals
  • Block and head faces: flatness
  • Gears, splines and keyways
  • Pistons and ring grooves

What you get

A measurement you can act on, and keep.

  • Wear map and sections

    A colour map of where metal has gone, with thickness and section cuts at the points that matter.

  • A graded report

    Pass, monitor or fail against the limits for that part, as a PDF with the figures in a spreadsheet.

  • Scans you keep

    The scan data itself, so the next scan can be compared with this one on the same alignment.

Vibration says look. A scan says how much.

Use scanning with condition monitoring to decide what to repair, what to rebuild and what can stay in service. Mining Intelligence grades motor circuit, vibration, oil and thermal readings and raises the alert that tells you which part to look at.

See the platform

How a scan job works

From the part to a graded report in four steps.

  1. Scope

    We agree the part, what to measure, the tolerance you need and the limits to grade against.

  2. Scan

    A laser scanner records the surface of the part as a cloud of 3D points.

  3. Compare

    The scan is aligned to the part as it was made, or to an earlier scan, and every point is measured.

  4. Report

    A wear map, section cuts and a graded report, with the figures in a spreadsheet and the scan data to keep.

Questions

What people ask about 3D scanning.

How accurate is a 3D scan?

It depends on the part, its surface and size, and the scanner used. We agree the tolerance you need before we start, and the report says what was achieved.

What can you measure?

Wear and the thickness that is left, pitch stretch on chains, diameter, ovality and taper on bores and journals, and the flatness of faces.

What is the scan compared with?

With the part as it was made, or with an earlier scan of the same part aligned the same way, so wear can be followed from one scan to the next.

Who sets the limits?

They are agreed with you before the job, for example from the manufacturer’s wear limits or your own maintenance standards. Each measurement is graded pass, monitor or fail against them.

What do we get at the end?

A wear map with thickness and section cuts at the points that matter, a graded PDF report with the figures in a spreadsheet, and the scan data itself, to compare with the next scan.

Do we need the Mining Intelligence platform?

No. 3D scanning is a service on its own. Used with condition monitoring, the readings tell you where to look and the scan tells you how much is left.

Have a part you need measured?

Tell us the part and what you need to know. We agree the tolerance and the limits with you before we scan.

Email opens your email app and WhatsApp opens a chat, with the details filled in. Nothing is sent until you press send.
Ask about scanning